FURUNO LS 4100 PDF

The Furuno LS is the little brother to the LS with a slightly smaller screen size, but with all of the power and features to satisfy both entry level and more. Furuno LS Fishfinder is a high contrast monochrome fishfinder with a large screen designed for small craft. Furuno LS has 5 display pages including. The Furuno LS is a dual frequency fish finder designed for small pleasure craft. It features a waterproof 5” high-definition silver bright LCD.

Author: Mukus Dobei
Country: Peru
Language: English (Spanish)
Genre: Finance
Published (Last): 21 April 2011
Pages: 452
PDF File Size: 4.36 Mb
ePub File Size: 2.71 Mb
ISBN: 959-1-87717-302-9
Downloads: 80983
Price: Free* [*Free Regsitration Required]
Uploader: Kesho

A warning label is attached to the equipment. Do not remove the label. No user-serviceable parts inside. The installer of the equipment is solely responsible for the proper installation furunno the equipment.

Use the specified power cable. Comprised of a display unit and a transducer, the LS displays underwater conditions on a bright 5-inch monochrome LCD. Automatic function permits unattended adjustment of range and gain.

FURUNO LS Fishfinder | eBay

Selects basic display range. The unit beeps, the startup screen appears, and then the equipment 44100 the ROM and RAM for proper operation and displays program number. The time remaining until power is turned off is counted down on the screen. Single frequency display 50 kHz The sounder uses ultrasonic signals to detect bottom conditions. The lower the frequency of the signal, the wider the detection area. Therefore, the 50 kHz frequency is useful for general detection and judging bottom condition.

This mode is useful for determining bottom contour. When the bottom depth increases, the display shift to keep the bottom echo at the lower part of the screen. Main, System and Installation. Below is the basic menu operating procedure. Page 1 or Page 2 of the main menu appears depending on the page last used. The auto mode in use is shown as Auto-Fishing or Auto-Cruising at the top left corner on the screen.

Basic ranges default 3. Shifting the range The basic range may be shifted up or down in the manual mode as follows: Window can be shifted up and down to select the depth. Display Range and display shift concept 1.

To suppress interference, do the following: Appearance of weak echoes These weak echoes may be erased as follows: The water temperature, arrival and l alarms require appropriate sensors.

  IRRLICHT DOCUMENTATION PDF

Depth, temperature, speed setting window Press the [MARK] key again. Exit Waypoint list 4. Position cannot be found. Fish school clearly shown White line Requires appropriate nav data. Choose the water type with which to use the LS, from Salt or Fresh. Turn key beep on or off. Turn the battery voltage indication appears at the top right corner on the screen fruno or off. Set range of each of the eight basic Only qualified personnel should work inside the equipment. Checking the items listed in the table below monthly will fkruno keep your equipment in good shape for years to come.

Troubleshooting table If… Then check … neither echo nor battery voltage. For any NG, furuo service. A special connector is required to test the NMEA port. Nothing appears if no connector is connected.

When choosing a location keep the following in mind: Keep the display unit out of direct sunlight. For planing hulls, a practical location is generally rather far astern, so that the transducer is always in water regardless of the planing attitude. Construction of fairing block 3. Drill a hole just large enough to pass the threaded stuffing tube of the transducer through the hull, making sure it is drilled vertically. Apply a sufficient amount of high quality caulking compound to the top surface of the transducer, ruruno the threads of the stuffing tube and inside the mounting hole and fairing This may require a certain amount of experimentation for fine tuning at high cruising speeds.

Fill the gap between the wedge front of the lz and transom with epoxy material to eliminate any air spaces. Necessary tools You will need the following tools: Sandpaper Silicone sealant Silicone grease Remarks on installation Mounting location To ensure the best performance, the sensor must be submerged in aeration-free and turbulence-free water.

Mount the sensor close to the centerline of the boat. Always wear safety goggles and a dust mask. Repeat step 1 to ensure that the angle of the sensor is correct. Do not position the sensor farther into the water than necessary fuduno avoid increasing drag, spray, and water noise and reducing boat speed. Position the second cable clamp halfway between the first clamp and the cable hole.

Mark this mounting hole. If a hole has been drilled in the transom, open the appropriate slot in the transom cable cover. Position the cover over the cable where it enters the hull. Coat with silicone sealant. Refer to the interconnection diagram to connect cables.

  CASIO EXILIM EX V8 MANUAL PDF

Leave slack in cables to facilitate checking and maintenance.

The transmission speed for both input and output is bps. Data is output at two-second intervals. Choose On to output input data. Outputs the data sentences of LS only. Outputs the data sentences of LS and sentences which are input from other equipment. To restore normal operation, turn off the power and then turn it on again.

WAAS is currently in the developmental phase. During the developmental phase the reliability and availability of the WAAS signal cannot be guaranteed.

Therefore, any position data should be verified against other sources to confirm reliability. Page of 48 Go. Table of Contents Add to my manuals Add. Electronic chart display and information system pages.

Furuno LS-4100 Fishfinder

Electronic chart display and information system ecdis pages. Page 3 A warning label is attached to the equipment. Page 4 The installer of the equipment is solely responsible for the proper installation of the equipment. Foreword Comprised of a display unit and a transducer, the LS displays underwater conditions on a bright 5-inch monochrome LCD. Operation Selects basic display furyno.

Dual Frequency Display Single frequency fuurno 50 kHz The sounder uses ultrasonic signals to detect bottom conditions. Menu Operating Procedure 1. Page 13 Basic ranges default 3. Erasing Weak Echoes 1. Setting Up Nav Data Displays 1. Other Menu Items Temperature Depth Page 25 Requires appropriate nav data.

Page 31 submerged, even when the boat is os, pitching or up on a plane at high speed. Transom Mount Transducer Construction of fairing block 3. Page 36 Transom hole: Wiring Coat with silicone sealant.

Iec Data Sentences 4.

Installation Menu Choose On to output input data. Page 48 All rights reserved. Comments to this Manuals Your Name. Enter text from picture: By pressing ‘print’ button you will print only current page. To print the ffuruno completely, please, download it.