CCNP SWITCH 6.0 INSTRUCTOR LAB MANUAL PDF

CCNP SWITCH 6 – BitRadius. Instructor Lab Manual Book everyone. Download file Free Book PDF Ccnp Switch Instructor Lab Manual at. CCNP: Implementing Secure Converged Wide-area Networks v – Lab Copyright © Ensure that the switch is set up so that both the router and host are in the same. VLAN. .. Figure Internet Explorer Security Alert Prompt. ccnp switch instructor lab pdf. CCNP SWITCH Instructor Lab Manual. This document is exclusive property of Cisco Systems, Inc.

Author: Dirg Dole
Country: Pacific Islands
Language: English (Spanish)
Genre: Travel
Published (Last): 23 December 2015
Pages: 104
PDF File Size: 11.77 Mb
ePub File Size: 15.53 Mb
ISBN: 385-8-61485-133-5
Downloads: 17725
Price: Free* [*Free Regsitration Required]
Uploader: Akinodal

The lab configuration files for the course should be in flash under the tshoot directory for a. Configure the ports going to the access points to be in VLAN Use the show spanning-tree command to check how the non-configured switches created a spanning tree. Configure UDLD globally for all fiber-optic gigabit interfaces for future use using the udld enable command. Use the show interfaces trunk command on DLS1.

Which is the active router for 30 and 40? The instance number can be between 0 and Display spanning tree information. The switches are connected via an Change the VLAN status to deactivate ports. Then an agreement is established as to which links to keep active and which links to logically remove from the spanning tree disable if multiple links exist.

Ccnp Tshoot Lab Manual Configuration Files – downloadsoftspecialists

If there is more than one choice in square brackets, the default is the option in capital letters. Configure the four switches as shown in the diagram with a hostname.

  GRAMTICA DE CELSO CUNHA & LINDLEY CINTRA PDF

For this scenario, configure ALS1 to load-balance by both source and destination MAC addresses using the global configuration command port-channel load-balance method, where the method is ccnpp mac. Both are acceptable and demonstrate the alternate methods for assigning VLAN ranges. Configure an access list on DLS1 called temp-host using the ip access-list extended name command. Now, bring up the port by issuing the no shutdown command on the interface.

Please see documentation for more details. The switch warns you about the possibility of creating switching loops. To verify the configuration, you can use the show interface summary, show wlan summary, and show run-config commands on the WLAN controller.

AZSV Model revision number: You can use other routers such as orswitches such asand Cisco IOS Software versions if they have comparable capabilities and features.

switc The table does not include any other type of interface, even though a specific router might contain one. Configure the virtual gateway IP address as 1.

Lastly, you will configure a VACL that allows a host on the staff network to be set up to use the VLAN for access but keeps the host isolated from the rest of the staff machines. Example from the Engineering instructkr Demonstrate root guard functionality.

CCNP SWITCH Lab Manual, 2nd Edition

The switches can use different methods to load-balance traffic going through a port channel. In this case, there would be two allowed MAC addresses. Inter-VLAN routing will be covered in a later lab.

Which VLANs are currently allowed on the ihstructor created trunks? No labs for this chapter. What is the default hold time? This command replaces the ip sla monitor responder command. Switch reload System configuration has been modified.

  2004 CHEVY TRAILBLAZER MANUAL PDF

Blocking can occur on the access layer switch or the distribution layer switch. The show ip cef detail command shows CEF operation in detail for the switch.

Remove all VLAN information lqb configurations that may have been previously entered into the switches. In the following sample output from ALS1, notice the three EtherChannels on the access and distribution layer switches. The default VTP mode for the and switches is server mode. In this lab, you will see what happens when the default spanning tree behavior is modified. For example, the following command is for a switch. Management traffic usually includes traffic for managing the switches, including VTP frames.

The CCNP certification requires candidates to pass three 1. By default, the UDP jitter operation repeats every 60 seconds. The switchport mode private-vlan host command sets the mode on the interface and the switchport private-vlan host-association primary-vlan-id secondary-vlan-id command assigns the appropriate VLANs to the interface.

Notice that you can modify spanning tree attributes in ranges. B0 Motherboard revision number: Lab Securing Layer 2 Switches. The two ports have equal costs because they have switcy same speed. Based on the various design considerations, you can choose UDLD or the loop guard feature or both.