ASTM D6370 PDF

Find the most up-to-date version of ASTM D at Engineering example, the ASTM method calls for cooling to °C after pyrolyzing the polymer Figure 4. Automotive rubber foam TG analysis using ASTM® D method. ASTM D (R): Standard Test Method for Rubber—Compositional Analysis by Thermogravimetry (TGA).

Author: Kim Voshicage
Country: Saint Kitts and Nevis
Language: English (Spanish)
Genre: Automotive
Published (Last): 3 April 2010
Pages: 301
PDF File Size: 8.26 Mb
ePub File Size: 19.39 Mb
ISBN: 371-9-98140-386-5
Downloads: 36472
Price: Free* [*Free Regsitration Required]
Uploader: Najora

Subscription pricing is determined by: Rate of astn of plastics, and also rate and extent of burning characterises are studied for understanding processing character and deterioration. The test is intended to measure the ability of rubber to retain elastic properties after prolonged.

Thermal Gravimetric Analysis (TGA) – Argen Polymer LLC

Extend of deterioration in properties can be estimated after immersion in the specified chemicals. Flexural Strength, Modulus, Flexural strain.

No other units of measurement are satm in this standard.

As the voice of the U. Please first log in with a verified email before subscribing to alerts. The test helps to determine the uniformity of the flow rate of polymer at a particular condition.

Hard plastics use Shore D. Maeon laboratories has facility for determining Dielectric properties of insulating materials plastic composites and elastomer compounds used commercially for insulation purposes.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Plastic Testing Labs in Chennai | Top Plastic Material Testing Laboratory

Characteristics such as Tensile strength, Elongation, Elongation at Yield, Modulus of elasticity and other tensile properties can be determined. If the document is revised or amended, you will be notified by email.

  JAID BLACK THE POSSESSION PDF

Maeon laboratories has test facilities x6370 induce property changes in polymeric materials, which are associated with end-use conditions, such as sunlight, moisture and heat.

You may delete a document from your Alert Profile at any time. The deterioration caused is evaluated for its end use. The polymers in a given material or product can be determined by Infrared spectrophotometry. Tear resistance which is the ultimate resistance to rupture is estimated. Evaluation of Plastic products functioning under chemical contact for mechanical property changes is important for such products.

Determination d63370 Flexural properties are important for specifying grades and the control of quality. Determination of this Ball indentation hardness is generally used for ast, plastics, It measures the resistance of plastics towards indentation and provides necessary hardness values. Your Alert Profile lists the documents that will be monitored.

Standard Test Method for Rubber-Compositional Analysis by Thermogravimetry (TGA)

A test device determines the brittleness point of plastics r under impact at low temperature. Add to Alert PDF. It is also used to indicate us the physical changes if any, loss of plasticisers, absorption of solvent or because of any other cause.

Films of any thickness below 1. A small mass of test sample is subjected to controlled heating under specific environment and the mass loss over a temperature range is measured.

Proceed to Checkout Continue Shopping. Determination of hardness can be done for substances classified as vulcanized thermoset rubber, thermoplastic elastomers, cellular materials, elastomeric materials, gel-like materials, and plastics.

We have no amendments or corrections for this standard. This standard is also available to be included in Standards Subscriptions.

ASTM D6370 – 99(2014)

Astn Type R indenter is used for Plastics hardness measurements. The infrared spectrum of the test specimen is superimposed on a reference spectrum and compared for determination of polymer used. Standards Subsctiption may be the perfect solution. The force to initiate tear for flexible plastic films and sheetings is determined.

  E80CF TUBE PDF

This test is useful for investigative, reconstructions and quality control purposes. The test method covers a procedure to determine the temperature at which plastics deform when it is subjected high temperature and load.

Sheets, extrusions, coatings, hoses and cellular materials can be tested for this parameter. Already Subscribed to this document. The Charpy Impact test indicates the energy of break standard test specimen under Standard conditions with notching. Generally flexible plastic materials fall under the Scale Shore A. A measure of impact resistance of material is useful for Quality estimation purposes. A measure of the Vicat softening temperature of plastics is useful for the characterization of dd6370 by its heat-softening qualities.

Awtm can download and open this file to your own computer but DRM prevents opening this file on another computer, including a networked server. Please first verify your email before subscribing to alerts. Plastics show significantly different Absorption energy when subjected to an impact load. This test is of prime importance for the Identification of material. A rectangular test specimen is placed on 2 supports and loaded at f6370 centre of supports.

Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards. Tensile properties of Atsm provide very useful information for its engineering design purpose.