ASTM D1622 PDF

GeoTesting Express is a provider of Geosynthetic Testing Services – ASTM D,Standard Test Method for Apparent Density of Rigid Cellular Plastics. View Abstract. Product Details. Detail Summary. View all details. Superseded By: ASTM D/DM. EN. Format. Details. Price (USD). PDF. ASTM D – Designation: D – 08 Standard Test Method for Apparent Density of Rigid.

Author: Bajind Kazishura
Country: Grenada
Language: English (Spanish)
Genre: Spiritual
Published (Last): 24 May 2015
Pages: 285
PDF File Size: 7.97 Mb
ePub File Size: 3.5 Mb
ISBN: 976-6-81828-233-3
Downloads: 22083
Price: Free* [*Free Regsitration Required]
Uploader: Tolkree

A number in parentheses indicates the year of last reapproval. This standard has been approved for use by agencies of the Department of Defense.

Density can be evaluated as the apparent overall density includes forming skins or by apparent core density forming skins removed.

The values given in parentheses are for information only. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

If the material does not have forming skins, the term overall density is not applicable.

Any test specimen preparation, conditioning, dimensions, or testing parameters, or combination thereof, covered in the relevant ASTM materials speci? If there d122 no relevant ASTM material speci?

ASTM D / DM – 14 Standard Test Method for Apparent Density of Rigid Cellular Plastics

In this case, the test specimen is the entire sample. Current edition approved April 1, Originally approved in Last previous edition approved in as D – Spray equipment shall be adjusted to the best d122 pattern and optimum performance.

Spray apply a minimum 1. After a minimum of 5 min, spray apply a second layer of 3.

  COMPLEX NUMBERS IN GEOMETRY - I.M.YAGLOM PDF

ASTM D Densimeter for Plastic Measurement

For calculation of core density, remove the bottom layer and the top skin. For calculation of the apparent overall density, cut a specimen that includes the forming skin. The specimens shall be taken from locations distributed throughout the sample. Number of Specimens 8. Hold the pressure of the dial foot to 2. In these cases the pressure shall be reduced accordingly.

When a sliding caliper gage is used, the proper setting shall be that point at which the measuring faces of the gage contact the surfaces of the specimen without compressing them. Do not use a steel rule for dimensions less than 25 mm 1 in. Measure all dimensions to a precision of In general, three measurements shall be made of each dimension.

A lesser number may be made when the following conditions apply: Measurements per Dimension 1 2 NOTE 3—The air buoyancy effect will vary with time and depends on the open-cell content of the foam. Highly ast materials are essentially air-? However, freshly produced closed-cell materials are essentially air-void and will exhibit maximum buoyant effects of air. SR is the between-laboratories standard deviation of the average.

VR is the between-laboratories coefficient of variation of the average. Precision and Bias4 For each material, all the samples were prepared at one source, but the individual specimens were prepared at the laboratories that tested them. Each test result was the average of? Each laboratory obtained one test result for each material. Users of d122 test method should apply the principles outlined in Practice E to generate data speci?

Standard Test Method for Apparent Density of Rigid Cellular Plastics

The principles of There are no recognized standards on which to base an estimate of bias for this test method. Thus, the value of Wa is zero in the above calculation when the sample is at equilibrium with the air. In this case the calculation for density is identical to the calculation in April 1, 1 Added new 1. Revised Average value d122 Material 3 in Table 1.

  HANDVEST VAN DE VERENIGDE NATIES PDF

Revised Material 4 repeatability interval, Ir. Revised Average value for Material 3 in Table 2. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Users of asym standard are expressly advised that asgm of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?

Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the responsible r1622 committee, which you may attend.

If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the aatm address or at phonefaxor service astm.